Skip to content
Pool Chemical Log

How to Lower Total Alkalinity in a Pool

Updated

At a glance

The range this guide is about
  • 60–180 ppmTotal alkalinity: Not tested. Range 60–180 ppm, MAHC 2024, a public-pool code.

Not a colour chart: read your strip against its own bottle.

Only acid lowers total alkalinity, and it lowers pH with it. Correct the reading for CYA first, add acid in portions (Indiana's health department caps it at one quart per 10,000 gallons, then retests 12 hours later), and let pH drift back up as carbon dioxide leaves the water.

Do the arithmetic
Pool pH and alkalinity calculator Open the pool ph and alkalinity calculator
Sources

Checked on ; next check .

PHTA (industry guidance)
80–100 ppm: For calcium hypochlorite, lithium hypochlorite, or sodium hypochlorite
PHTA (industry guidance)
100–120 ppm: For sodium dichlor, trichlor, chlorine gas or BCDMH
Photograph of gentle ripples from a return jet across the clear deep end of a backyard pool
On this page

High total alkalinity makes pH stubborn: it keeps drifting up, and every acid dose seems to wear off. The only way to bring alkalinity down is acid, the same muriatic acid or dry acid (sodium bisulfate) that lowers pH, so lowering alkalinity means lowering pH too, then letting it recover. This guide sets out how to tell whether the reading is really high, how to add the acid in portions you can control, and how to bring pH back without pushing alkalinity up again. The amount for your own pool comes from the pH and alkalinity calculator, which sizes it from your gallons and the strength on your acid's label.

Is it really too high?

The MAHC 2024, a public-pool code, sets a range of 60 to 180 ppm. PHTA, industry guidance, sets narrower ideal bands by sanitizer: 80 to 100 ppm where a salt chlorine generator, calcium hypochlorite or sodium hypochlorite is used, because those push pH up, and 100 to 120 ppm for dichlor and trichlor, which push it down. A pool using liquid chlorine at 130 ppm is above its ideal band but inside the code's range, which makes it a balance problem, not an emergency. The guidance for public pools in the MAHC Annex makes the same point for public pools: minor deviations in alkalinity aren't an imminent health threat on their own.

Before treating a high reading, allow for stabilizer. Cyanuric acid shows up in the alkalinity test, so a stabilized pool reads higher than its carbonate alkalinity really is. The correction given by the MAHC Annex, guidance for public pools, is to divide the CYA reading by 3 and subtract that from the measured total alkalinity; PHTA gives a more exact factor that depends on pH. A pool reading 120 ppm with 90 ppm of CYA has a corrected alkalinity of about 90 ppm, which may need nothing at all. The calculator applies PHTA's factor for you.

Worked example: alkalinity at 160 ppm in a 20,000-gallon pool

A 20,000-gallon plaster pool on liquid chlorine tests at 160 ppm total alkalinity, pH 7.8 and 30 ppm CYA. Corrected for stabilizer, alkalinity is still about 150 ppm, well above PHTA's 80 to 100 ppm band for this sanitizer, so it is worth bringing down to about 100 ppm. The calculator sizes the whole muriatic acid dose from those readings.

The whole dose doesn't go in at once. Indiana's health department says not to add more than one quart of acid per 10,000 gallons at a time, and to retest 12 hours later before the next adjustment. For this pool that is at most two quarts per round. The first round goes in with the pump running, poured slowly in one spot in the deep end, and the floor there is brushed afterward. Twelve hours later alkalinity and pH are retested and written into a pool chemistry log entry; pH has dropped to about 7.2. The next round waits until pH has come back up, and the job takes several days.

The method, step by step

  1. Test total alkalinity, pH and CYA together, and correct alkalinity for CYA as above.
  2. Size the total dose with the pH and alkalinity calculator, using the strength printed on your acid.
  3. Split it into portions. Indiana's limit is one quart per 10,000 gallons in any one adjustment, with a retest 12 hours later. Its broader advice is to make slight adjustments early rather than letting alkalinity drift far and correcting it all at once.
  4. Add the acid where it does the most to alkalinity. Indiana's method for lowering alkalinity without dropping pH as far is to pour the acid in the deep end, in pint-sized portions, standing in one place so it forms a column of very low pH water. In that column, carbonate alkalinity turns into carbon dioxide, which gasses off. Brush the floor afterward, because acid is heavier than water and can etch the surface where it settles.
  5. Retest after 12 hours, then repeat until alkalinity reaches its target.
  6. Let pH come back up. See below.

How pH recovers without raising alkalinity

Every portion of acid lowers pH as well. Adding soda ash or baking soda to raise it would put back the alkalinity you just removed, so the better route is time and air. PHTA explains that water with high carbonate alkalinity tends to drift up in pH as carbon dioxide escapes into the air. Running the pump with the returns pointed up to ripple the surface, a spillover or a fountain all speed that escape, and pH rises while alkalinity stays where the acid left it. Keep pH inside CDC's 7.0 to 7.8 for home pools while you work, and pause the next acid round if pH is already near the bottom of that range.

Three published rules of thumb, and why they disagree

For 10,000 gallons and a 10 ppm drop, PHTA gives about 1.6 pints of 31% muriatic acid or 2.1 pounds of 94% dry acid. Toledo-Lucas County's health department gives about 26 oz of muriatic acid or 2.15 lbs of dry acid, close to PHTA. The MAHC Annex, guidance for public pools, gives 1.3 quarts of muriatic acid or 1.6 pounds of dry acid, without naming a strength, and its muriatic figure is noticeably higher than the other two. That gap is one reason this page sends you to the calculator for the amount: it works from the strength on your own label rather than a single assumed product.

Handling the acid

Muriatic acid gives off fumes and burns skin and eyes. Read the label, wear gloves and eye protection, and work with the wind behind you. Indiana's sheet says to dilute acid by pouring it slowly into water, never water into acid, to avoid damaging the pool's walls. Never pour acid into the skimmer or mix it with chlorine; why that matters is explained in never mix these pool chemicals. If alkalinity keeps climbing back however often you lower it, have a pool service technician check the fill water and the pool's chemistry as a whole.

Sources (6)

Get new tools by email

When we add a tool to Pool Chemical Log, we'll send you one short email. Nothing else.