Skip to content
Pool Chemical Log

Hot Tub Chemical Levels: Chlorine, Bromine, pH and Temperature

Updated

Hot tub chemical levels: CDC for home hot tubs, and the MAHC 2024, a public-pool code
ReadingCDC, for home hot tubsMAHC 2024, a public-pool codeMAHC section
Free chlorineAt least 3 ppmAt least 3.0 ppm for spas5.7.3.1.1.2.3
Free chlorine, upper limitNot setNo higher than the product label allows5.7.3.1.1.5
Bromine, if used instead of chlorineNot setAt least 4.00 ppm for spas, no more than 8.0 ppm while open to bathers5.7.3.1.2.2 and 5.7.3.1.2.3
pH7.0–7.87.0–7.85.7.3.4.1
Cyanuric acid (CYA) and products that contain itDo not useNot for new spas; existing spas to stop within 4 years of the code's adoption5.7.3.1.3.1 and 5.7.3.1.3.1.1
Water temperature, upper limitNot set104°F (40°C)5.7.4.7.2
Total alkalinityNot set60–180 ppm5.7.4.4.1
Combined chlorine (chloramines)Not setAct to lower it above 0.4 ppm5.7.4.4.2
Calcium hardnessNot setNo more than 2,500 ppm5.7.4.4.3
How often to test chlorine and pHAt least twice a day, more when several people use the tubBefore opening each day5.7.5.1

The MAHC is written for public spas. Its Annex, guidance for public pools, describes a range of 3–5 ppm free chlorine for spas as a margin of safety above the 3.0 ppm minimum (5.7.3.1.1.2).

In short: CDC asks for at least 3 ppm free chlorine and pH 7.0–7.8 in a hot tub, with no cyanuric acid. The MAHC 2024, a public-pool code, adds a 4.00 ppm bromine minimum for spas, an 8.0 ppm bromine ceiling and a 104°F (40°C) water temperature limit.

These figures are copied from the sources listed on this page, as published; they aren't instructions for any one product. Follow the label on the product you use, and your local health code if your pool is public.

Get new tools by email

When we add a tool to Pool Chemical Log, we'll send you one short email. Nothing else.

Hot tub water is demanding to keep right. It is small, so one soaker changes the chemistry noticeably, the water is warm enough to burn chlorine off quickly, and people sit in it for a long time with the jets running. This chart sets out the figure CDC gives a home hot tub owner for each reading beside the figure the CDC's Model Aquatic Health Code, a public-pool code, sets for spas, with the section of that code on every line so each number can be checked against the original. It is written for hot tub owners; if you also keep a pool, the ideal pool chemical levels chart covers that water, where the figures differ.

Why a hot tub gets its own numbers

CDC treats the two kinds of water differently on one point above all: the chlorine minimum. For a pool it asks for at least 1 ppm; for a hot tub it asks for at least 3 ppm, and it recommends keeping cyanuric acid (CYA, the stabilizer in dichlor and trichlor) out of a hot tub altogether. The pH range, 7.0 to 7.8, is the same as for a pool.

The MAHC 2024 is a public-pool code, so it governs public spas, not a backyard tub. Its Annex, guidance for public pools, explains why it sets a higher spa minimum: spas have a higher peak bather load, warmer water and, sometimes, bathers at greater risk, and the heat favors microbial growth and can use chlorine up fast. A home tub shares the heat and the small volume, which is why the public-spa figures are a sensible check on a private tub, even though no code binds you to them.

Worked example: a tub that reads fine at a glance

Say a tub that has been dosed with dichlor tests at 2 ppm free chlorine, pH 7.9, 90 ppm total alkalinity, 0.6 ppm combined chlorine and a water temperature of 104°F. Against the chart:

  • Free chlorine is low. CDC and the MAHC 2024, a public-pool code, both ask for 3 ppm or more in a spa, and 2 ppm, which would pass in an unstabilized pool, does not.
  • pH is high. 7.9 sits just over the 7.0–7.8 that both sources share.
  • Combined chlorine is high. The code asks the operator to act once it passes 0.4 ppm, and 0.6 ppm has.
  • Temperature is at the limit, not over it. The code's maximum is 104°F (40°C).
  • Alkalinity is inside the code's 60–180 ppm.
  • The product is the problem underneath. Dichlor carries cyanuric acid, which CDC advises against in a hot tub, so the longer-term fix is a chlorine product without it, chosen from the spa-use directions on a label.

The order matters here as in a pool: alkalinity steadies pH, so check it before chasing the pH number. None of this site's calculators is built for a hot tub, so take the amount from the product's own label for your tub's volume.

Chlorine or bromine

Both sanitizers are in the chart because both are common in hot tubs. The MAHC 2024, a public-pool code, sets 4.00 ppm as the minimum bromine for a spa and 8.0 ppm as the most bromine allowed while bathers are in the water. A bromine test kit reads total bromine; the Annex, guidance for public pools, says the figure it gives is total bromine, not the free halogen measured with chlorine.

Bromine's appeal in a tub is how it behaves at a higher pH. The same Annex, guidance for public pools, notes that at pH 7.5 about 94% of bromine is in its active form against 49% for chlorine with no CYA, and at pH 8.0 it is 83% against 23%. Hot tub pH tends to creep upward, which is why bromine holds up better there. That also makes the pH row the one to watch whichever sanitizer you use.

The industry reads the ranges a little differently. PHTA, the Pool & Hot Tub Alliance, gives spa free chlorine a minimum of 2.0 ppm, an ideal of 3.0 to 5.0 ppm and a maximum of 10.0 ppm in its pool and spa management guidelines, and puts the ideal total bromine at 4.0 to 6.0 ppm. This chart follows CDC and the public-pool code, which give minimums rather than ideals. The Annex, guidance for public pools, adds that an operating range of 3 to 5 ppm free chlorine in a spa leaves a margin of safety above the minimum.

Heat, jets and why the reading falls

CDC lists what uses chlorine up in any pool or hot tub: sweat, urine, dirt, sunlight and the droplets thrown off by jets. A hot tub has all of them in a small volume. That is why CDC asks for tests at least twice a day, and more often when several people use the tub. The same page warns that a DPD test can bleach out above 10 ppm and show a false low or zero, which matters after a heavy dose.

Do not read CDC's table of germ-kill times as a promise for your tub. It is calculated for 1 ppm of free chlorine at pH 7.5 and 77°F with no CYA, a cooler and quieter water than a hot tub.

When to get help

Water that goes cloudy, foams, smells of chlorine despite a good reading, or leaves swimmers with a rash is a reason to stop and retest, not to add more product. The Annex, guidance for public pools, notes that Pseudomonas aeruginosa, a common culprit in spa skin disease outbreaks, was found to return rapidly in spas when chlorine fell below 3.0 ppm or bromine below 6.0 ppm. If a reading will not hold after a correct dose, or the problem involves the heater, pump or wiring, call a pool service technician or a licensed electrician. Keep a dated record of each test in the pool chemistry log, and see what cyanuric acid does for why stabilizer is a poor fit for a hot tub.