Skip to content
Pool Chemical Log

Pool Pump Not Priming? A Troubleshooter for Air in the Pump Basket

Updated

Pool pump not priming troubleshooter

For a pool pump that runs without pulling water, fills its basket with air, or catches prime and then loses it. Answer what you can see at the pump and the skimmer; each question rules out one cause, cheapest first.

What is the pump doing?

Look through the clear lid of the pump's strainer pot if it has one. A pot full of water means the pump has prime; a pot of air or churning foam means it has lost it.

It runs, but the strainer pot stays empty or full of air

Where is the pool's water level against the skimmer opening?

The skimmer is the rectangular opening in the pool wall at the waterline.

Below the opening, or only just at its bottom edge

Deal with it soon

The water level is too low, so the skimmer is drawing air

MSU Extension's pump troubleshooting gives a pool water level below the skimmer as a cause of a pump that runs with no water, and it says the level must be above the bottom of the skimmer opening. Once the level falls that far, the skimmer gulps air with every wave, the air collects in the pump and the pump loses prime.

What to do

  1. Switch the pump off so it doesn't run without water.
  2. Top the pool up with a hose until the water is well above the bottom of the skimmer opening.
  3. Refill the strainer pot with water from a bucket or hose, close the lid firmly, and restart.
  4. If the level keeps dropping faster than evaporation explains, note how fast in the log; a leak in the pool or plumbing needs a pool service technician.
Comfortably above the bottom of the opening

With the pump switched off, what do the skimmer and pump baskets look like?

Packed with leaves, hair or debris

Deal with it soon

A clogged basket or impeller is starving the pump of water

MSU lists a clogged hair strainer, a clogged impeller and a closed valve among the causes of a pump that runs while moving little water. A skimmer basket packed with leaves does the same thing one step earlier: water can't reach the pump fast enough, so it pulls air instead.

What to do

  1. Switch the pump off at its switch or breaker before opening anything.
  2. Empty every skimmer basket, then open the strainer pot and empty its basket.
  3. Refill the pot with water, check the lid's seal is clean and seated, close it and restart.
  4. If the baskets were clear and the pump still moves little water, the impeller may be blocked. MSU's fix is to clean the pump's parts; open the pump only as its manual directs, or have a pool service technician do it.
Clear, or only a little debris

What about the valves and where the pump sits?

Suction valves are the ones on the pipes coming from the pool to the pump, before it.

A suction valve is closed or only part open

Deal with it soon

A closed suction valve leaves the pump nothing to pull

MSU's list for a pump that runs with no water includes a closed valve, and it says the suction-side valves must be open. A valve left half shut after winterizing, opening or a repair is one of the easiest causes to miss.

What to do

  1. Switch the pump off before you move any valve.
  2. Open the valves from the skimmer and main drain fully. If you have several skimmer lines, open them all.
  3. Never close every valve at once. MSU warns that doing so can damage the pump or the filter.
  4. Refill the strainer pot, close the lid and restart.
The pump sits well above the pool's water level

Deal with it soon

The pump may be too far above the water to catch prime

MSU gives a pump set above the water level beyond its maker's recommendation as a cause of a pump that runs with no water. Its notes on draining a pool add that most self-priming pumps will lift water eight feet or more once they are running, but will not pick up a prime from more than four feet. A pump that holds prime all season can still fail to catch it from empty.

What to do

  1. Check the lift limit in your pump's manual against the height from the pool's water level to the pump.
  2. Fill the strainer pot completely before each start, and give the pump a few minutes to pull the water up the suction line.
  3. If it still won't catch, fill the suction line itself through the strainer pot until it stops taking water, then restart.
  4. A pump that sits too high for its rating needs to be moved or swapped for one rated for the lift. That is a job for a pool service technician.
Valves open, pump near water level, and it still won't prime

Deal with it soon

Air is leaking into the suction side

Everything between the pool and the pump runs under suction, so a leak there pulls air in rather than letting water out, and nothing drips. MSU names air leaks on the suction side as the cause of a pump that loses prime, and says to look for them with soap and water around the strainer basket and the suction pipe connections.

What to do

  1. Start with the strainer pot lid: clean its seal and the groove it sits in, check the seal isn't cracked or flattened, and close the lid evenly.
  2. With the pump running, brush soapy water over the pot lid, the drain plugs, the unions and the pipe joints before the pump. Where air is drawn in, the soap film is pulled in or bubbles.
  3. Tighten a loose union by hand and replace a seal that is worn. Leave cracked pipe or a split fitting to a pool service technician.
  4. If you can find no leak and the pump still fills with air, a technician can pressure-test the suction line.
It primes, then loses prime after a while

When does it lose prime?

After the water level drops, from evaporation, splash-out or backwashing

Deal with it soon

The water level is too low, so the skimmer is drawing air

MSU Extension's pump troubleshooting gives a pool water level below the skimmer as a cause of a pump that runs with no water, and it says the level must be above the bottom of the skimmer opening. Once the level falls that far, the skimmer gulps air with every wave, the air collects in the pump and the pump loses prime.

What to do

  1. Switch the pump off so it doesn't run without water.
  2. Top the pool up with a hose until the water is well above the bottom of the skimmer opening.
  3. Refill the strainer pot with water from a bucket or hose, close the lid firmly, and restart.
  4. If the level keeps dropping faster than evaporation explains, note how fast in the log; a leak in the pool or plumbing needs a pool service technician.
There are always bubbles in the strainer pot, and it gets worse

Deal with it soon

Air is leaking into the suction side

Everything between the pool and the pump runs under suction, so a leak there pulls air in rather than letting water out, and nothing drips. MSU names air leaks on the suction side as the cause of a pump that loses prime, and says to look for them with soap and water around the strainer basket and the suction pipe connections.

What to do

  1. Start with the strainer pot lid: clean its seal and the groove it sits in, check the seal isn't cracked or flattened, and close the lid evenly.
  2. With the pump running, brush soapy water over the pot lid, the drain plugs, the unions and the pipe joints before the pump. Where air is drawn in, the soap film is pulled in or bubbles.
  3. Tighten a loose union by hand and replace a seal that is worn. Leave cracked pipe or a split fitting to a pool service technician.
  4. If you can find no leak and the pump still fills with air, a technician can pressure-test the suction line.
When the skimmer basket fills up

Deal with it soon

A clogged basket or impeller is starving the pump of water

MSU lists a clogged hair strainer, a clogged impeller and a closed valve among the causes of a pump that runs while moving little water. A skimmer basket packed with leaves does the same thing one step earlier: water can't reach the pump fast enough, so it pulls air instead.

What to do

  1. Switch the pump off at its switch or breaker before opening anything.
  2. Empty every skimmer basket, then open the strainer pot and empty its basket.
  3. Refill the pot with water, check the lid's seal is clean and seated, close it and restart.
  4. If the baskets were clear and the pump still moves little water, the impeller may be blocked. MSU's fix is to clean the pump's parts; open the pump only as its manual directs, or have a pool service technician do it.
When I connect the vacuum hose

Keep an eye on it

The vacuum hose is bringing air with it

A manual vacuum hose that goes on full of air sends that air straight to the pump. MSU also says the hose must be in good repair, with any hose that has holes replaced, and that the pump's suction has to be adequate when the vacuum runs through the skimmer.

What to do

  1. If the pump has already lost prime, switch it off, refill the strainer pot and restart it before you connect the hose.
  2. Fill the hose completely: hold its end against a return jet, or feed it into the water from the vacuum head end until no more bubbles come out.
  3. Connect the full hose at the skimmer quickly, with the end kept under water.
  4. Check the hose for splits and holes along its length, and replace it if you find any.
It won't prime after opening, draining or servicing the pool

Keep an eye on it

After opening or draining, the pump has to be primed by hand

A pump whose lines were drained has nothing to start with. MSU's start-up order is to prime the pump before starting the filter, then run it to fill the filter tank and bleed the air out through the tank's air vent. Plugs left out after winterizing, or a drain plug that was never refitted, let air straight in.

What to do

  1. Switch the pump off. Check that every drain plug on the pump, strainer pot and filter is back in, with its seal.
  2. Check that the water level is above the bottom of the skimmer opening and the suction valves are open.
  3. Fill the strainer pot right to the top with water, close the lid firmly, and start the pump.
  4. Open the filter's air relief valve while it primes, and close it once a steady stream of water comes out.
  5. If the pot hasn't filled within a few minutes, switch off, top up the pot again and retry. If it still won't catch, work through the air-leak and lift branches.
It hums, won't start, trips the breaker or smells hot

Act now

A pump that hums or trips the breaker is an electrical fault

This isn't a priming problem. MSU's list for a pump that won't run includes a blown fuse, low voltage, loose or broken wiring and a defective motor, and for sparks or smoke it says to turn the power off immediately and call a qualified service technician.

What to do

  1. Switch the pump off at the breaker and leave it off.
  2. Don't open the motor or touch the wiring, and don't keep resetting a breaker that trips.
  3. Call a licensed electrician for the supply and wiring, and the pump maker or a pool service technician for the motor.
  4. Until it's fixed the water isn't being filtered or sanitized by the equipment: test it, and log what you add.
My salt chlorinator shows a no-flow warning

Deal with it soon

A no-flow warning on a salt system often means lost prime

The Jandy and Pentair salt chlorinator manuals both list a pump that has lost prime as a cause of their no-flow condition, alongside a cell plugged with debris, and both say to prime the pump if necessary. The chlorinator stops making chlorine without flow, so the warning protects the cell; the pump is the thing to fix.

What to do

  1. Look at the pump's strainer pot. If it is full of air, start this troubleshooter again from the top and pick the first answer.
  2. If the pump has prime and water is moving, check the cell for debris lodged between its plates.
  3. Once flow is back, watch that the warning clears, and follow the salt cell troubleshooter if it doesn't.

In short: A pool pump that won't prime is short of water or drawing air: low water at the skimmer, a clogged basket, a closed suction valve, too much lift or a suction-side leak. MSU Extension notes most self-priming pumps lift water eight feet or more once running, but won't pick up a prime from more than four.

This troubleshooter narrows down likely causes from published guidance; it can't see or test your water. Retest before you add anything, follow the label on every product you use, and call a pool service technician or a licensed electrician for anything electrical, gas-fired or structural.

Get new tools by email

When we add a tool to Pool Chemical Log, we'll send you one short email. Nothing else.

A pump that runs with its strainer pot full of air isn't moving water through the filter, the heater or a salt cell, and it shouldn't be left running that way. This troubleshooter works through the causes in the order that costs least to check: the water level, the baskets, the valves, the height of the pump above the water, and finally an air leak somewhere on the suction side. It is written for a home pool owner standing at the equipment pad, and its main source is the pump troubleshooting appendix in Michigan State University Extension's manual for training pool operators. The Jandy and Pentair salt chlorinator manuals add the one case a salt pool owner sees first: a no-flow warning.

Worked example: a pump that won't catch after opening

An in-ground pool is opened in spring. The winter cover is off, the water is topped up and the pump is switched on, but after several minutes the clear lid of the strainer pot shows only churning air. The tree asks what the pump is doing, and the answer for a pump that won't prime after opening leads to the start-up branch. Its first check is the plugs: one of the two drain plugs on the strainer pot is still sitting in the skimmer basket where it was left in autumn. With the pump off, the plug goes back in with its seal, the pot is filled to the brim from a hose, and the lid is closed evenly.

On restart the pot fills within a minute, then slowly grows a bubble at the top. That points to the air-leak branch. Soapy water brushed over the lid ring is pulled in at one spot: the lid's seal has a flat section from a winter under pressure. A new seal, a clean groove and the bubble is gone. Opening the filter's air relief valve until water spurts out finishes the job. Writing both the seal change and the restart pressure into a pool chemistry log entry gives a baseline for the season.

Why a pump loses prime

A pool pump is built to push water, not to pull air. Everything between the pool and the pump runs under suction, so a fault there doesn't leak water onto the pad; it pulls air in, quietly. MSU's list for a pump that runs with no water names air pockets and leaks in the suction line, a water level below the skimmer, a closed valve, too high a suction lift and incorrect line voltage. For a pump that loses prime after running, its causes are air leaks on the suction side, to be found with soap and water around the strainer basket and the pipe connections, and air carried in from the pool when the level is too low for the skimmer.

What the answers mean

A low level is the first and cheapest thing to check. MSU says the water must sit above the bottom of the skimmer opening; below that the skimmer swallows air with every ripple, and a long run of backwashing, splash-out or hot dry weather can take it there.

A clogged basket or impeller starves the pump. Leaves in a skimmer basket or hair in the pump's strainer slow the water so much that the pump draws air through whatever gap it can find.

A closed valve gives the pump nothing to pull. After any repair or season change, every suction valve should be fully open, and MSU warns against ever closing all the valves at once.

Too much lift is the cause most easily overlooked. MSU's note on draining a pool explains that most self-priming pumps will lift water eight feet or more once they are running, but won't pick up a prime from more than four feet. A pump that runs happily all summer can still refuse to start from empty if it sits well above the waterline.

An air leak is what remains. The lid seal of the strainer pot, the pot's drain plugs, the unions and any joint on the suction pipe can all let air in without dripping.

Salt systems: the no-flow warning

The Jandy AquaPure and Pentair IntelliChlor manuals both list a pump that has lost prime as a cause of their no-flow condition, next to a cell plugged with debris. The chlorinator stops making chlorine without flow, so the pool can run short of chlorine for days before anyone looks at the pump. The salt cell troubleshooter covers the warning once the pump is moving water again.

When to call for help

Stop and switch off at the breaker if the motor hums without turning, trips its breaker, smells hot or sparks. MSU's advice for sparks or smoke is to turn the power off immediately and call a qualified service technician, and wiring belongs to a licensed electrician. A pool service technician is also the right call for cracked pipe, a pump that needs moving, or a suction leak you can't find, since the line can be pressure-tested. If water moves but the returns are still weak, the pool filter troubleshooter takes over from here, and a pump that gulps air only when the vacuum hose goes on is covered in how to vacuum a pool.