Skip to content
Pool Chemical Log

Pool Filter Troubleshooter: High Pressure, Weak Returns and Dirt Blowing Back

Updated

Pool filter troubleshooter

For a sand, cartridge or D.E. filter that is running at the wrong pressure, giving weak returns, letting dirt or media back into the pool, or needing cleaning too often. Pick the symptom, then your filter type.

What is the filter doing?

The pressure gauge reads high

What type of filter is it?

A high-rate sand filter has a backwash valve and a tank of sand. A D.E. filter has a backwash valve and takes a white powder. A cartridge filter opens up and has pleated elements.

Sand

Deal with it soon

Sand filter: backwash when pressure is 10 to 12 psi over clean

MSU Extension says to backwash a sand filter when the incoming pressure is 10 to 12 psi higher than a clean filter's, when flow drops, or when the water turns cloudy with debris left in it. Typically the difference between the inlet and outlet gauges should not exceed 12 to 15 psi, although some equipment is designed for a higher one.

What to do

  1. Switch the pump off, move the valve to Backwash, and restart. Backwash for 2 to 3 minutes, or until the discharge runs clear.
  2. Switch the pump off again, return the valve to Filter, and restart. Write down the new clean pressure.
  3. If the gauge climbs back within days, go to the short-runs branch. Floc, debris and scale all shorten runs.
  4. If you've added a flocculant, check the gauge first: pressure rises fast after one goes in. At 10 to 12 psi above normal, backwash to waste, which may have to be repeated several times.
  5. MSU cautions against using D.E. powder in a sand filter as a routine fix, because it can hide a filter, impeller or circulation problem that needs a closer look.
Cartridge

Deal with it soon

Cartridge filter: clean the element, and use your own clean pressure

The saved MSU manual gives no pressure-rise figure for a cartridge filter, so there is no number to quote. Log the pressure when the element is new or freshly cleaned, and follow the filter maker's manual for when to clean. MSU explains that a cartridge filter has no backwash: the element is hosed off, and the element must be cleaned or replaced as a whole.

What to do

  1. Switch the pump off, release the pressure, and take the element out. Wash off the dirt with a hose and nozzle. Never scrub the pleats with a brush.
  2. If it still feels greasy, MSU's next step is a one-hour soak in a solution of one cup of automatic dishwasher detergent to five gallons of water, to lift body oils.
  3. Look for the contaminants MSU names: algae, calcium carbonate, iron or the binders in chlorine tablets. These need a special cleaning, such as an acid soak with a neutralizing rinse, and the maker's instructions come first. Acid needs gloves and eye protection.
  4. Keep a second set of elements so the filter is not out of service while one set dries.
  5. A hot tub's element gets clogged with body oils faster than a pool's, so clean it more often.
Diatomaceous earth (D.E.)

Deal with it soon

D.E. filter: backwash at a 10 to 20 psi differential, then recoat

MSU says to backwash a pressure D.E. filter when the inlet and outlet gauges show a 10 to 20 psi differential, depending on the design; a vacuum D.E. filter goes at about 10 to 15 inches of mercury. Backwashing also strips the powder coating, so the filter must be recoated before it is back in service.

What to do

  1. Backwash as your manual directs. Switch the pump off whenever you change the valve, and never close all the valves at once, which can damage the pump or the filter.
  2. Recoat using the amount on the filter's data plate. MSU's guide is 0.125 pound (2 ounces) of D.E. per square foot of filter area, mixed into a slurry first. Don't cut back on the amount.
  3. Don't let the first 15 to 30 minutes of filtered water go back to the pool if it is cloudy. Return it to waste or the recirculate setting until it runs clear.
  4. Never stop the pump for any reason except a backwash once the coating is on: a pause lets the coating fall off.
  5. If the differential keeps rising after a correct backwash and recoat, see the short-runs branch.
I don't know what the gauge read when the filter was clean

Keep an eye on it

Log a clean starting pressure first

A pressure reading means little without a clean starting point. The MSU Extension manual measures a dirty filter against a clean one, and the clean reading belongs to your filter, pump and plumbing, not to a table. The manual's own examples are gauges that read wrong when they were calibrated poorly, were mounted at different heights or had a clogged opening between the pipe and the gauge.

What to do

  1. Clean or backwash the filter as its manual directs, then run the pump at its normal speed with the valves in their normal positions.
  2. Write down the gauge reading once it settles, with the date, in the note on a pool chemistry log entry. This is the number to compare against from now on.
  3. If you have two gauges, one before and one after the filter, also note the difference between them.
  4. Check the gauges: MSU names a badly calibrated gauge, two gauges mounted at different heights and a clogged opening between the pipe and the gauge as causes of false readings.
  5. Then follow your filter's manual for the cleaning point. MSU gives figures for sand and D.E. filters but none for cartridges.
The returns are weak, or the pump looks like it is struggling

What does the pump basket show?

Switch the pump off before you open the basket lid, and refill the pump with water before you restart it.

Packed with debris, or water barely moves in it

Deal with it soon

A blocked basket, skimmer or impeller is starving the pump

MSU's troubleshooting list ties a pump that runs but moves little water to a clogged hair strainer, a clogged impeller or a valve left closed. Low pressure with a packed basket means too little water is reaching the pump, not that the filter is clean.

What to do

  1. Switch the pump off. Empty the basket, and clear the skimmer baskets too.
  2. Check that every valve on the suction and the return side is fully open.
  3. If the basket was clear and flow is still weak, the impeller may be clogged. MSU's fix is to clean the pump parts. Open the pump only as its manual directs.
  4. Refill the pump with water before restarting it, then watch the gauge. Log the new reading.
Air bubbles, or no water, and the pump loses prime

Deal with it soon

Air is getting into the suction side

MSU lists air pockets and leaks on the suction side as the cause of a pump that runs without moving water, loses prime, or moves water slowly in its basket. It adds two more: a pool water level below the skimmer opening, and a pump set too high above the water. Air bubbles in the filter or returns point the same way.

What to do

  1. Check the water level first. It has to sit above the bottom of the skimmer opening, or the pump sucks air.
  2. Check the strainer basket and the pipe connections on the suction side. MSU suggests a soap-and-water test for leaks: bubbles form where air is drawn in.
  3. Check the valves on the suction side, which must be open.
  4. Prime the pump properly and bleed the air from the filter tank before restarting. If the pump still won't prime, a pool service technician can pressure-test the suction line.
It looks normal, but the gauge reads high and the returns are weak

What type of filter is it?

A high-rate sand filter has a backwash valve and a tank of sand. A D.E. filter has a backwash valve and takes a white powder. A cartridge filter opens up and has pleated elements.

Sand

Deal with it soon

Sand filter: backwash when pressure is 10 to 12 psi over clean

MSU Extension says to backwash a sand filter when the incoming pressure is 10 to 12 psi higher than a clean filter's, when flow drops, or when the water turns cloudy with debris left in it. Typically the difference between the inlet and outlet gauges should not exceed 12 to 15 psi, although some equipment is designed for a higher one.

What to do

  1. Switch the pump off, move the valve to Backwash, and restart. Backwash for 2 to 3 minutes, or until the discharge runs clear.
  2. Switch the pump off again, return the valve to Filter, and restart. Write down the new clean pressure.
  3. If the gauge climbs back within days, go to the short-runs branch. Floc, debris and scale all shorten runs.
  4. If you've added a flocculant, check the gauge first: pressure rises fast after one goes in. At 10 to 12 psi above normal, backwash to waste, which may have to be repeated several times.
  5. MSU cautions against using D.E. powder in a sand filter as a routine fix, because it can hide a filter, impeller or circulation problem that needs a closer look.
Cartridge

Deal with it soon

Cartridge filter: clean the element, and use your own clean pressure

The saved MSU manual gives no pressure-rise figure for a cartridge filter, so there is no number to quote. Log the pressure when the element is new or freshly cleaned, and follow the filter maker's manual for when to clean. MSU explains that a cartridge filter has no backwash: the element is hosed off, and the element must be cleaned or replaced as a whole.

What to do

  1. Switch the pump off, release the pressure, and take the element out. Wash off the dirt with a hose and nozzle. Never scrub the pleats with a brush.
  2. If it still feels greasy, MSU's next step is a one-hour soak in a solution of one cup of automatic dishwasher detergent to five gallons of water, to lift body oils.
  3. Look for the contaminants MSU names: algae, calcium carbonate, iron or the binders in chlorine tablets. These need a special cleaning, such as an acid soak with a neutralizing rinse, and the maker's instructions come first. Acid needs gloves and eye protection.
  4. Keep a second set of elements so the filter is not out of service while one set dries.
  5. A hot tub's element gets clogged with body oils faster than a pool's, so clean it more often.
Diatomaceous earth (D.E.)

Deal with it soon

D.E. filter: backwash at a 10 to 20 psi differential, then recoat

MSU says to backwash a pressure D.E. filter when the inlet and outlet gauges show a 10 to 20 psi differential, depending on the design; a vacuum D.E. filter goes at about 10 to 15 inches of mercury. Backwashing also strips the powder coating, so the filter must be recoated before it is back in service.

What to do

  1. Backwash as your manual directs. Switch the pump off whenever you change the valve, and never close all the valves at once, which can damage the pump or the filter.
  2. Recoat using the amount on the filter's data plate. MSU's guide is 0.125 pound (2 ounces) of D.E. per square foot of filter area, mixed into a slurry first. Don't cut back on the amount.
  3. Don't let the first 15 to 30 minutes of filtered water go back to the pool if it is cloudy. Return it to waste or the recirculate setting until it runs clear.
  4. Never stop the pump for any reason except a backwash once the coating is on: a pause lets the coating fall off.
  5. If the differential keeps rising after a correct backwash and recoat, see the short-runs branch.
I don't know what the gauge read when the filter was clean

Keep an eye on it

Log a clean starting pressure first

A pressure reading means little without a clean starting point. The MSU Extension manual measures a dirty filter against a clean one, and the clean reading belongs to your filter, pump and plumbing, not to a table. The manual's own examples are gauges that read wrong when they were calibrated poorly, were mounted at different heights or had a clogged opening between the pipe and the gauge.

What to do

  1. Clean or backwash the filter as its manual directs, then run the pump at its normal speed with the valves in their normal positions.
  2. Write down the gauge reading once it settles, with the date, in the note on a pool chemistry log entry. This is the number to compare against from now on.
  3. If you have two gauges, one before and one after the filter, also note the difference between them.
  4. Check the gauges: MSU names a badly calibrated gauge, two gauges mounted at different heights and a clogged opening between the pipe and the gauge as causes of false readings.
  5. Then follow your filter's manual for the cleaning point. MSU gives figures for sand and D.E. filters but none for cartridges.
It looks normal and the gauge reads low

Deal with it soon

Low pressure with a normal basket: find the restriction before the pump

A low gauge with a clear basket means the pump isn't pushing as hard as it should, or something between the pool and the pump is restricting it. MSU's list for a pump that starts and then stops includes a clogged filter, a closed or partly closed valve and a motor wired wrongly, and it advises checking the turnover rate with a vacuum gauge and the pump curve.

What to do

  1. Recheck the valves, especially any that were touched during recent service.
  2. Check the filter's own clean pressure from your log. A clean filter on a healthy pump should match it.
  3. Compare the real flow to the pump curve in its manual if you have a flow meter. A shortfall means a restriction, an air leak or a worn pump.
  4. If the pump starts and stops on its own, or the motor looks to be wired wrongly, a licensed electrician or the pump maker should look at it.
The pump doesn't run, hums, smokes or sparks

Act now

A pump that won't run, hums or sparks is an electrical problem

MSU gives these as electrical and motor faults: a blown fuse of the wrong size, low voltage, loose or broken wiring, or a defective motor, and for sparks or smoke it says to turn the power off immediately and call a qualified service technician.

What to do

  1. Switch the pump off at the breaker. Don't touch the wiring or reset a breaker repeatedly.
  2. Call a licensed electrician for the supply, breaker or wiring, and the pump maker or a pool service technician for the motor.
  3. Until it's repaired the pool isn't being filtered or sanitized by its equipment: keep an eye on the water and use the log.
Sand, D.E. powder or fine dirt is coming back into the pool

What is coming back into the pool?

Sand, in the pool or at the return fittings

Deal with it soon

Sand in the pool means a cracked lateral or a valve that isn't seated

MSU Extension says that sand found entering the pool through the wall inlets means either a cracked or broken lateral, or that the backwash lever was not properly set in place. The laterals are the finger-like pieces at the bottom of the tank that the sand is packed around.

What to do

  1. Check the valve handle first: make sure it is fully seated in Filter, not stopped part-way between positions.
  2. Backwash and rinse, then look at the return fittings again. If sand still arrives, a lateral has probably cracked.
  3. A lateral replacement means emptying the tank. Have a pool service technician or the filter maker's service do it.
  4. Vacuum the sand out of the pool rather than leaving it to be walked on.
D.E. powder, a white cloud or film

Deal with it soon

D.E. in the pool: damaged grids or gaskets, or a missing coating

MSU lists damaged or misplaced filter grids as the cause when D.E. powder turns up in the pool, and damaged gaskets, elements or other internal parts as a way for powder and dirt to pass through and cloud the water. A coating that fell off because the pump was stopped lets water pass through bare areas of the grid.

What to do

  1. Switch off, open the filter and inspect each grid for cracks, tears and misalignment. MSU's repair is to fix or replace the grids and check them for cracks.
  2. Check the gaskets and seals for damage.
  3. If the grids are fine, the powder may have come from a new recoat that went back to the pool too early. Let the first 15 to 30 minutes run to waste next time.
  4. Vacuum the powder out of the pool, and recoat the filter correctly.
Fine dirt and cloudy water, with a cartridge filter

Deal with it soon

Cartridge filters: inspect the element and its seals

The saved sources don't describe how a cartridge filter lets dirt through, so this is the one case where the tree can only point you to the filter's manual. MSU describes the element as fiber that traps dirt and suspended matter as water passes through it, so a torn or collapsed element or a poor seal would let water bypass it.

What to do

  1. Switch off and open the filter. Check the element for tears, crushed pleats or a cracked end cap, and check the seals.
  2. Replace the element if it is damaged. MSU says the whole element is replaced with a cleaned or new unit.
  3. If the water is cloudy rather than the filter leaking dirt, test and balance it; see the green pool guide.
It needs cleaning again soon after I clean it

What type of filter is it?

Sand

Deal with it soon

Sand filter runs are short: floc, debris and scale

MSU's troubleshooting list for short runs on a high-rate sand filter has three causes: floc has entered the pool (adjust the alum feed), excess debris in the pool, and scale-forming water. The MAHC Annex, guidance for public pools, adds that scale can restrict flow and shorten filter runs.

What to do

  1. Stop or reduce any alum or flocculant you're adding, and vacuum the settled floc to waste rather than through the filter.
  2. Skim or screen floating debris and vacuum settled dirt before it reaches the filter.
  3. Test pH, calcium hardness and alkalinity, and work out the saturation index. Water that is scale-forming needs rebalancing.
  4. Log the interval between backwashes so you can see whether the changes help.
Cartridge

Deal with it soon

Cartridge runs are short: too much flow, oils, or a coated element

MSU says flow above 0.375 gpm per square foot of cartridge area shortens the filter cycle and reduces filtration effectiveness. It also says that hot water releases more body oil, and that algae, calcium carbonate, iron and chlorine-tablet binders on the element call for special cleaning.

What to do

  1. Check the pump is not pushing more water than the filter is rated for; the filter's data plate and manual give its rated flow.
  2. Clean the element thoroughly with a hose, then with the detergent soak MSU describes if it is greasy.
  3. Test the water for iron and calcium scale. A coated element needs the maker's special cleaning, and the source of the coating has to be fixed.
  4. Keep a spare set so cleaning doesn't mean going without a filter.
Diatomaceous earth (D.E.)

Deal with it soon

D.E. runs are short: coating, dirt load, flow and chemistry

MSU lists 13 causes of short D.E. runs. The common ones are a heavy dirt load, the wrong grade or amount of D.E., clogged baskets, a partly lost coating, oil, hair, lotion or algae slime, an incomplete backwash that leaves the old coating on, a compacted coating from too much flow, air trapped in the tank, calcium on the elements when pH rises above 7.8, and an undissolved glaze of calcium hypochlorite. Alum must never be used in a D.E. filter.

What to do

  1. Clean the skimmer and pump baskets, and reduce the dirt load before it reaches the filter.
  2. Recoat with the amount your manual specifies. Don't cut it back to save powder.
  3. Check the flow rate against the design rate. MSU says to adjust valves to hold it, as too much flow compacts the coating.
  4. Keep pH down at 7.8 or below, and dissolve calcium hypochlorite fully before it goes in the pool.
  5. If runs stay short after a correct recoat, the filter may need to be opened and the grids cleaned; that's a job for the manual or a service technician.

In short: Michigan State University Extension says to backwash a sand filter when the incoming pressure is 10 to 12 psi above the clean-filter reading, and a pressure D.E. filter at a 10 to 20 psi gauge difference. It gives no such figure for cartridges, so log your own clean pressure and follow the filter's manual.

This troubleshooter narrows down likely causes from published guidance; it can't see or test your water. Retest before you add anything, follow the label on every product you use, and call a pool service technician or a licensed electrician for anything electrical, gas-fired or structural.

Get new tools by email

When we add a tool to Pool Chemical Log, we'll send you one short email. Nothing else.

A filter fails in a handful of ways, and each one shows on the gauge, in the returns or in the water. This troubleshooter starts from the symptom (high pressure, weak returns, sand or powder in the pool, or runs that get short) and then asks the type of filter, because a sand filter, a cartridge filter and a D.E. filter are cleaned and fail differently. It is for a home pool owner with a pressure gauge on the filter and the manual for the equipment nearby. Its main source is the Michigan State University Extension pool manual, a training text for pool operators.

Worked example: a sand filter that has climbed 12 psi

A 20,000-gallon pool with a high-rate sand filter ran at 14 psi right after its last backwash, a reading written into the note on a log entry at the time. Today the gauge says 26 psi and the returns are noticeably weaker. The tree starts with the high-pressure branch and asks the filter type. For sand, MSU Extension says to backwash when the incoming pressure is 10 to 12 psi greater than on a clean filter. The gauge is 12 psi over, so the filter is due.

The backwash itself runs for 2 to 3 minutes, or until the water at the discharge runs clear. The pump goes off for each valve change. The new reading after the valve returns to Filter is the new baseline: if it comes back near 14 psi, the filter has recovered. If the gauge was back at 26 psi three days later, the tree's short-runs branch applies, and MSU's three causes for a sand filter are floc that has reached the filter, excess debris and scale-forming water.

The log is what made that example work. With no clean reading on file, a 26 psi gauge could have meant almost anything.

Log the clean pressure first

Every pressure rule in the source is relative: it measures the gauge against a clean filter, or one gauge against the other. MSU Extension gives a number for sand filters, a differential for D.E. filters and none for cartridges. Where no number exists, the honest answer is to record the reading right after a thorough cleaning, with the pump at its usual speed and the valves in their usual positions, and compare later readings with it. The filter maker's manual sets the cleaning point for your model, and some equipment is designed to run at a higher difference than typical.

The gauge needs to be trusted. MSU names three ways it can mislead: poor calibration, two gauges mounted at different heights so that they disagree, and a clogged opening between the pipe and the gauge. A reading that jumps without a reason is more often a gauge fault than a filter fault.

Sand, cartridge and D.E.: what the source says for each

Sand. Backwash when the pressure is 10 to 12 psi over clean, when flow drops, or when the water is cloudy with debris left in it. MSU also notes that the inlet and outlet gauges typically differ by no more than 12 to 15 psi, and that flocculant raises pressure quickly once it is added. It cautions against using D.E. powder in a sand filter as a routine fix, because it can mask a filter, pump or circulation problem that deserves a proper look.

Cartridge. There is no backwash. The element comes out and is washed with a hose and nozzle, never with a brush. For oil, MSU's step is a one-hour soak in a solution of dishwasher detergent. For algae, calcium carbonate, iron or tablet binders, special cleaning applies, and the filter maker's instructions come first. Spa cartridges clog faster because hot water releases more body oil. The pressure at which to clean isn't given anywhere in the source.

D.E. Backwash a pressure D.E. filter when the two gauges differ by 10 to 20 psi, depending on the design. The coating has to be rebuilt after each backwash, at about 0.125 pound of D.E. per square foot of filter area, and the pump must not be stopped while the coating is on, or it falls off the grids.

Low pressure and weak returns usually start before the filter

A dirty filter gives weak returns and a high gauge. A low gauge with weak returns means the pump is not getting enough water, so look upstream. MSU's pump troubleshooting list attributes a pump that moves little water to a clogged strainer basket, a clogged impeller, a closed valve, an air leak on the suction side or a pool level below the skimmer opening. A leak that draws air can be found with soapy water, which bubbles where air is drawn in. Only after those are cleared is the filter itself the likely suspect. A pump that won't run, hums, smokes or sparks is electrical, and belongs to a licensed electrician or the pump maker.

Blowback: sand, powder and fine dirt

Sand arriving in the pool means a cracked lateral inside the tank or a backwash handle that isn't fully seated, and the lateral is a repair for a service technician. D.E. powder in the pool points to damaged grids, gaskets or elements, or to a coating that was put back in service before the first filtered water ran clear. MSU describes no failure mode for a cartridge that lets fine dirt through, so the advice there is a visual check of the element and its seals.

Why runs get short

Short runs usually come from what reaches the filter. Heavy debris, oils and lotions, algae slime and poorly dissolved chemicals all clog it, and so does mineral scale. The MAHC Annex, guidance for public pools, says the following: "Scale can restrict water flow, shortening filter runs and reducing filtration efficiency." Balanced water protects the filter as well as the surfaces; the pool LSI calculator shows which way yours leans, and the ideal levels chart gives the ranges to aim for. A salt chlorine generator can flag a dirty filter too, since low flow trips its safety switch; see the salt cell troubleshooter.

When to get help

Open a filter tank only as its manual says, with the pump off and the pressure released. Replacing laterals, grids or a pump motor, and any wiring, are service jobs. When the water is cloudy or green and the filter seems fine, the filter is only part of the answer; the green pool guide sets out the sequence. Put each cleaning and its pressure in the note on an entry in the pool chemistry log.