When Can You Swim After Adding Chemicals? The Label's Re-entry Line
Updated
| Product | What the label says before swimming | EPA Reg. No. |
|---|---|---|
| Liquid chlorine, 12.5% sodium hypochlorite | "Re-entry into treated swimming pools is prohibited above levels of 4 ppm of chlorine due to risk of bodily harm." After a superchlorination: "Do not reenter pool until the chlorine residual is between 1.0 and 4.0 ppm." | 82357-1 |
| Liquid chlorine, 12.5% sodium hypochlorite (a second label) | After a superchlorination: "Do not enter pool until the chlorine residual drops below 4.0 PPM." | 55852-3 |
| Liquid chlorine, 10% sodium hypochlorite | "Do not enter pool until the free available chlorine residual is 1-4 ppm." "Re-entry into treated swimming pools is prohibited above levels of 4 ppm chlorine for risk of bodily injury." | 1258-1094 |
| Cal hypo (calcium hypochlorite), HTH Granular 73 | "Re-entry into treated pools is prohibited above 4 ppm due to risk of bodily harm." | 1258-1239 |
| Trichlor tablets | "Reentry into treated pools is prohibited above 3 ppm chlorine due to risk of bodily injury." | 42177-18 |
| Dichlor (dichlor dihydrate) | A paraphrase, not a quotation (this site's scan of the label is too garbled to quote): bathers should not be allowed to enter the pool until the chlorine residual has dropped to 3.0 ppm or less; another panel of the same label says the pool should not be entered until the chlorine residual is below 3.0 ppm, the stricter reading this site follows. | 7124-31 |
Each limit is a free chlorine reading in ppm, from that product's own EPA label. Test the water and compare the reading with the label on your container before anyone swims; a different brand's label may set a different line.
In short: The saved EPA labels set the swimming line as a free chlorine reading, not a clock time: no swimming above 4 ppm after liquid chlorine or cal hypo, above 3 ppm after trichlor, and 3.0 ppm for dichlor, where this site's scan of the label is garbled and paraphrased.
These figures are copied from the sources listed on this page, as published; they aren't instructions for any one product. Follow the label on the product you use, and your local health code if your pool is public.
Handling pool chemicals safely
In the words of the public-health agencies:
Chemicals shall be added to water when diluting as opposed to adding water to a concentrated chemical.
(MAHC 2024, 5.9.3.4.2.2 (a public-pool code) (PDF, opens in a new tab))Two or more chemicals shall never be mixed in the same dilution water.
(MAHC 2024, 5.9.3.4.2.3.1 (a public-pool code) (PDF, opens in a new tab))If label directs pre-dissolving, add the pool chemical to water. NEVER add water to the pool chemical because a violent (potentially explosive) reaction can occur.
(CDC, Use Pool Chemicals Safely (PDF, opens in a new tab))Store each pool chemical separately in a dedicated location.
(CDC, Pool Chemical Safety (opens in a new tab))Do not mix old chemicals with fresh chemical, even if they are the same type
(EPA 550-F-01-003 (PDF, opens in a new tab))Never mix:
(CDC, Use Pool Chemicals Safely (PDF, opens in a new tab))Chlorine products with acid; this could create toxic gases.
Different pool chemicals (for example, different types of chlorine products) with each other or with any other substance.
Get new tools by email
When we add a tool to Pool Chemical Log, we'll send you one short email. Nothing else.
After you shock a pool, the question is not how many hours to wait but what the test says. The EPA labels this site has saved set the line as a free chlorine reading in ppm, and the chart above gives each product's line next to its registration number, so you can match it to the label on your own container. It is written for the owner standing at the pool with a test kit and a freshly dosed pool. The pool shock calculator works out the dose and shows the same lines once your dose would push the pool past one.
Worked example: shocking with liquid chlorine
Say a pool is shocked on Saturday with 12.5% liquid chlorine to 10 ppm free chlorine, the top of the 5 to 10 ppm that the liquid chlorine labels give for a superchlorination. Here is what each reading means, using the liquid chlorine labels in the chart:
- Sunday morning, 6 ppm. Above the 4 ppm line on every liquid chlorine label saved here. Nobody swims.
- Monday morning, 3.5 ppm. Under 4 ppm, so the liquid chlorine labels allow it. The 10% label and EPA Reg. No. 82357-1 also set a floor of 1 ppm, which 3.5 clears.
- Same reading, dichlor. If the pool had been shocked with dichlor, 3.5 ppm would not clear its 3.0 ppm line, so the wait would go on.
No label gives a number of hours. How quickly chlorine falls depends on sunlight, heat, how much the swimmers use up and, in a stabilized pool, the cyanuric acid, so the test decides. CDC lists sunlight, sweat, dirt and jets among the things that reduce chlorine, which is why a pool can drop faster on one day than on the next.
Why the labels differ
Liquid chlorine and cal hypo labels stop swimming above 4 ppm. Trichlor stops it above 3 ppm. Dichlor sits at 3.0 ppm. Three details are worth reading closely.
The boundary. EPA Reg. No. 82357-1 prohibits re-entry above 4 ppm and, for a superchlorination, says to wait until the residual is between 1.0 and 4.0 ppm. EPA Reg. No. 55852-3 words it differently: "Do not enter pool until the chlorine residual drops below 4.0 PPM." A reading of exactly 4.0 ppm passes the first and fails the second, so use the stricter wording if the two could apply. The 10% label, EPA Reg. No. 1258-1094, says "Do not enter pool until the free available chlorine residual is 1-4 ppm."
The floor. Two labels give a lowest reading as well as a highest. CDC's minimum for a home pool without CYA is also 1 ppm, so a swim-ready pool is one inside the band, not just under the ceiling.
Dichlor's line is a paraphrase. The dichlor label, EPA Reg. No. 7124-31, is printed in three columns and this site's scan of it runs them together, so none of its sentences can be quoted word for word. What can be read is that one panel keeps bathers out until the residual has dropped to 3.0 ppm or less, and another until it is below 3.0 ppm. The chart carries the same attributed paraphrase as the shock calculator and follows the stricter of the two, so at exactly 3.0 ppm the answer for dichlor is to wait. Check the printed label on your own container for the real wording.
Trust the reading before you trust the zero
After a heavy dose the test itself can mislead. CDC warns that if the chlorine in the sample is more than 10 ppm, a DPD test might partly or entirely bleach out and read falsely low, or even 0 ppm. A reading of 0 the morning after a big shock is not proof that the water is safe; CDC's pool chemical page names dilution and higher-range test strips as ways to read a higher level. Retest before you trust it. Test the water before anyone gets in, and use the same kind of kit each time so the readings compare.
Acids, alkalinity products and the rest
No saved acid, baking soda or soda ash label or safety data sheet states a re-entry line, so this chart has no row for them and gives no wait it cannot source. Their hazard is mainly in the handling. The Indiana Department of Health's guidance for adjusting chemicals tells operators to add them dissolved and only when the pool is not in use, and the storage and handling checklist covers the rest. For a pH or alkalinity dose and the order to add them, see the pH and alkalinity calculator.
Hot tubs have their own line
Three of the labels carry a separate line for a spa or hot tub. EPA Reg. No. 82357-1 and the HTH cal hypo label, EPA Reg. No. 1258-1239, prohibit re-entry above 5 ppm, and the 10% label (EPA Reg. No. 1258-1094) calls for 3-5 ppm and prohibits it above 5 ppm. That fits CDC's higher chlorine minimum for a hot tub. The hot tub chemical levels chart gives the targets themselves.
When to get help
If a reading will not come down after a day or two, if the water is cloudy or smells strongly of chlorine while the test reads low, or if a swimmer has burning eyes, a cough or a rash, stay out and call a pool service technician. For exposure to a chemical itself, follow the first aid on the label and call a poison control center. The guide to reading a pool chemical label shows where to find the re-entry line on your own container.
Sources (9)
- EPA Reg. No. 82357-1, 12.5% sodium hypochlorite label (2020) www3.epa.gov
- EPA Reg. No. 55852-3, 12.5% sodium hypochlorite label (2017) www3.epa.gov
- EPA Reg. No. 1258-1094, 10% sodium hypochlorite label (2019) www3.epa.gov
- EPA Reg. No. 1258-1239, HTH Granular 73 calcium hypochlorite label (2025) www3.epa.gov
- EPA Reg. No. 42177-18, trichlor tablets label (2011) www3.epa.gov
- EPA Reg. No. 7124-31, dichlor dihydrate label (2004) www3.epa.gov
- CDC, Pool Chemical Safety cdc.gov
- CDC, Home Pool and Hot Tub Water Treatment and Testing cdc.gov
- Indiana Department of Health, Adjusting Chemical Levels in a Swimming Pool in.gov