Salt Cell Troubleshooter: Why Your Salt Chlorine Generator Isn't Making Chlorine
Updated
Salt cell troubleshooter
For a salt chlorine generator that isn't making chlorine. Start from what the control panel shows; where the cause depends on the brand, the tree asks which one and uses that maker's own manual.
What is the generator telling you?
Use the panel as it is right now. If it shows several lights, start with the flow light, then salt, then cell.
A flow warning (no flow, or a red flow light)
Act now
The generator stopped because it can't sense water flowing
A salt cell makes hydrogen gas as well as chlorine, and PHTA warns that running one without adequate water flow can cause an explosion. That is why every maker fits a flow switch or sensor that shuts the cell off. Hayward's No Flow light, Pentair's red Flow light, Jandy's No Flow display and CircuPool's No Flow light all mean the same thing: not enough water is passing through the cell, or the sensor can't tell that it is.
What to do
- Look at the pump first. Confirm it is primed, the strainer basket is clear and every valve is open. Pentair and Jandy both list a dirty filter among the causes, so clean or backwash the filter if its pressure is high.
- Hayward: check that the flow switch is plugged into the bottom of the control unit with an undamaged wire, that there is a straight run of pipe ahead of it (the manual asks for 12 inches), and that the arrows on the switch point the way the water flows.
- Jandy: confirm the flow, temperature and salinity sensor is plugged in and its contacts are free of glue, tape or debris, then switch the power off and on again so the unit re-reads it.
- CircuPool: look for air bubbles in the cell housing, and check that the flow switch paddle swings freely. On a variable-speed pump set low, raise the speed until the light goes out.
- Pentair: remove the cell and look for an obstruction if the pump and valves check out.
- If water is clearly moving and the light stays on, the switch or sensor has probably failed. Have the manufacturer or a pool service technician replace it. Never bypass a flow switch.
A salt warning (low, check, add or high salt)
Is the salt warning for too little salt or too much?
Too little (low salt, check salt or add salt)
Which generator is it?
The makers set different salt ranges and shut-off points, so the advice changes with the brand.
Hayward AquaRite
Deal with it soon
Hayward AquaRite: the salt level is below the range
On the AquaRite, a flashing Check Salt light means salt is under 2700 ppm and the unit is still running at reduced efficiency. A steady light means it is too low and the unit has shut down. Hayward's target is 3200 ppm within a 2700 to 3400 ppm range. Its troubleshooting list puts the low-salt cutoff at 2400 ppm, a different figure from the indicator description, so treat anything under 2700 ppm as low.
What to do
- Confirm the reading with a separate salt test. Hayward itself advises having the level checked before adding large quantities.
- Check that the correct Turbo Cell model is selected in the control's setup; the manual lists this first for both salt lights.
- Work out the pounds needed for your volume with the salt calculator, and add plain sodium chloride at least 99% pure with the pump running. Don't use rock salt, iodized salt or salt with anti-caking additives.
- Run the pump for 24 hours with suction from the main drain so the salt mixes. The display can take 24 hours to catch up.
- Recheck the free chlorine while the cell is off, and shock from an outside source if it is low.
Pentair IntelliChlor
Deal with it soon
Pentair IntelliChlor: the red salt light is on
Pentair's salt display shows red below 2800 ppm, meaning chlorine is made at reduced efficiency, and treats a level below 2600 ppm as very low: the unit turns off until salt is added. Pentair's range is 3600 to 4500 ppm, with 3600 ppm ideal. The salt sensor is only accurate to within 500 ppm either way.
What to do
- Test salt with a separate kit, since the built-in sensor can be off by 500 ppm. Heavy rain and a leak are the two causes the manual names.
- Use the salt calculator for the amount, and add salt as described in the manual. Let the pump run for at least 24 hours before reading the display again.
- If the cell light is also flashing green after 24 hours, take the cell out, look for scale and clean it if needed.
- While the unit is off, test free chlorine and keep it up with an outside source such as liquid chlorine.
Jandy AquaPure
Deal with it soon
Jandy AquaPure: the add-salt light or a low-salinity code
Jandy reads salt in grams per liter, where 1 gpl is 1000 ppm. The manual recommends 3.0 to 3.5 gpl. Below 2.0 gpl the system switches the cell off until the level is raised above 2.0 gpl, and the display shows service code 144. Code 175 can mean an air lock at the flow sensor or very low salinity.
What to do
- Verify the reading with a salt meter calibrated for sodium chloride or a titration kit. Jandy warns that salt test strips can vary by 400 to 800 ppm.
- Dirty or faulty sensor contacts can also give a false low reading, so clean the sensor contacts and check its cable.
- Add salt for your volume (the salt calculator does the sum) to bring the pool to 3.0 gpl, with the pump running and the chlorine production set to 00% while it dissolves.
- After the salt has mixed, switch the unit back on and press the salinity button a few times until the reading settles.
CircuPool CORE
Deal with it soon
CircuPool CORE: the Low Salt light is on
CircuPool's Low Salt light comes on under 2000 ppm. The ideal level is about 3500 ppm, and the manual suggests keeping salt between 3000 and 4000 ppm. The CORE keeps working across a very wide 2000 to 7000 ppm band, so a lit Low Salt light is a late warning: the pool has usually been under range for a while.
What to do
- Follow CircuPool's own order. Inspect the cell for mineral scale first and clean it if needed, because a dirty cell can trigger the same light.
- If the cell is clean, test the salt by hand with a separate kit. The manual advises adding large amounts in portions and retesting between them.
- Add pool-grade sodium chloride with the CORE switched off and the pump running; the salt can take 24 to 48 hours to dissolve in summer, longer in winter.
- Don't let salt sit below 3000 ppm once it is back in range.
Too much (high salt, or a flashing green salt light)
Which generator is it?
Hayward AquaRite
Deal with it soon
Hayward AquaRite: the High Salt light is on
A lit High Salt light means the salt level is too high and the AquaRite has shut down. Hayward's range tops out at 3400 ppm, and the manual says salt is generally tasted from about 3500 to 4000 ppm. Salt is not lost to evaporation, so the level doesn't fall on its own.
What to do
- Check the Turbo Cell model setting first, since Hayward lists a wrong model as a cause of this light.
- Confirm the level with a separate salt test.
- The only way to lower salt is to drain part of the pool and refill with fresh water. Hayward's instruction is to repeat until the level is back in range.
- Drain in stages and retest between them rather than guessing a volume.
Pentair IntelliChlor
Deal with it soon
Pentair IntelliChlor: the green salt light is flashing
A flashing green light means salt is above 4500 ppm, the top of Pentair's 3600 to 4500 ppm range. The manual warns that this raises the risk of corrosion and deterioration of equipment and surfaces in and around the pool.
What to do
- Verify with a separate test, since the sensor is only accurate to within 500 ppm.
- Dilute by draining some water and refilling with fresh water, as Pentair instructs, then run the pump for 24 hours and retest.
- Repeat in small steps until the reading is back near 3600 ppm.
Jandy AquaPure
Deal with it soon
Jandy AquaPure: an HH reading or service code 145
Code 145 means salinity above 4.0 gpl. An HH on the display means the reading is above 4.5 to 6.5 gpl, depending on temperature, and too high to measure. Jandy says operating with high salt will damage the power center, and that above 6.0 gpl it can corrode pool fixtures. The target is 3.0 to 3.5 gpl.
What to do
- Confirm the level with a salt meter calibrated for sodium chloride or a titration kit.
- Jandy's remedy is to partially drain the pool and dilute it with fresh water until salinity is back to 3.0 to 3.5 gpl. With a DE filter, backwash it too.
- Because Jandy says high salt damages the power center, keep chlorine production at 00% until the level is back under 4.0 gpl.
CircuPool CORE
Deal with it soon
CircuPool CORE: all lights flashing, or a reading above range
The CORE manual describes no separate High Salt light. Its all-lights-flashing state means salt may be greatly out of range, in either direction. The suggested range is 3000 to 4000 ppm, though the unit runs across 2000 to 7000 ppm. The saved manual gives no dilution procedure for high salt.
What to do
- Test the salt by hand before doing anything. A reading from 3000 to 4000 ppm needs no action.
- If the test is well above 4000 ppm, ask CircuPool support for its advice before draining. The other three makers dilute with fresh water, which is the likely remedy.
- Retest after any dilution, and keep a record of each reading.
I can't tell, or I don't trust the reading
Deal with it soon
Get a trustworthy salt reading before you do anything else
The generator's own salt display is an estimate. Pentair's sensor is accurate only to within 500 ppm, Jandy notes that temperature affects its reading and that test strips can vary by 400 to 800 ppm, and Hayward advises a separate check before large additions. The ranges differ by brand: Hayward 2700 to 3400 ppm, Pentair 3600 to 4500 ppm, Jandy 3.0 to 3.5 gpl and CircuPool 3000 to 4000 ppm.
What to do
- Test salt with a titration kit or a meter calibrated for sodium chloride, then compare it with your brand's range.
- After any addition, run the pump for 24 hours before testing again.
- Come back to this tree with the new reading.
A cell, service or power message
Which describes the message best?
Switch the generator off at the circuit breaker before you open anything.
An inspect-cell, clean-cell or flashing cell light, and I can take the cell out to look
With the cell out, what do you see between the plates?
Hold the cell up to a light and look through it from both ends.
Light-colored crusty or flaky deposits (scale)
Deal with it soon
Scale on the plates is cutting chlorine output
PHTA says scale will form inside a generator even when the water is balanced, mostly calcium carbonate, because the plate surfaces run at a high pH. Scale cuts the contact between water and plates, so chlorine output falls, and it also shields the plates from the cooling water, which can overheat and ruin the cell. Hayward's Inspect Cell light, Pentair's flashing green cell light, Jandy's code 125 and CircuPool's Clean Cell light are all the cell asking to be cleaned.
What to do
- Switch off at the breaker and take the cell out. Start with the gentlest method: a hose, with a plastic or wooden tool for stubborn flakes on a Hayward. Never use metal on the plates.
- Use acid only if rinsing fails, and only at the ratio and soak time in your own manual, which differ by brand. Add acid to water, wear gloves and eye protection, and keep the wiring end dry. PHTA warns that acid cleaning removes some of the plate coating and that too much will damage the cell.
- On a Hayward, hold the diagnostic button for 3 seconds after servicing to reset the Inspect Cell light.
- Fix why it scaled. Test calcium hardness, pH and alkalinity, and work out the saturation index; CircuPool ties frequent buildup to a high index.
- Pentair and Jandy both advise looking inside every 2 months at first, and going less often only after the inspections come up clean.
Leaves, grit or other debris
Deal with it soon
Debris is caught in the cell
Grit, leaves and bits of media that get past the filter can lodge on the plates or block the flow path. Hayward notes debris that passed through the filter catching on the plates, and Pentair and Jandy both list a clogged or dirty cell as a cause of low chlorine.
What to do
- Rinse the debris out with a hose, with the power off, and look through the cell again.
- Ask where it came from: a torn filter element, a cracked lateral in a sand filter or a missing basket will keep sending more.
- Refit the cell and watch the warning. If it returns within days, the filter is the real problem.
Clean plates, or the warning came back after a cleaning
Deal with it soon
A clean cell that still warns: check salt, setup and age
A cell warning on clean plates usually traces to low salt, a wrong setting or a worn cell. CircuPool says its Clean Cell light outranks the salinity lights, and that a light returning soon after cleaning means verify salinity and clean again. Hayward says that if Inspect Cell stays lit after a thorough cleaning with the right salt level, the cell may be worn and need replacing. Jandy's codes 120, 121 and 123 point to low current at the cell, and 125 asks for a cleaning.
What to do
- Test the salt with a separate kit and compare it with your brand's range.
- Hayward: make sure the Turbo Cell model chosen in setup matches the cell fitted. Pentair: a flashing cell light with low salt should be rechecked after 24 hours.
- Jandy: clean the cell, then check the DC cord and its contacts for dirt or corrosion.
- CircuPool: its Cell Life Low light is only an hours-based reminder, not a fault. Replace the cell when the unit can no longer reach its set output.
- If the cell is clean, the salt is right and the setup matches, the cell is likely worn. Contact the manufacturer for a replacement.
No power light, a circuit-board or voltage message, or a tripped breaker
Act now
A power, wiring or circuit-board fault: switch off and call for service
These messages aren't chemistry problems. Hayward shows -Pcb- with all four red and yellow lights on for a possible circuit-board fault. Pentair lists an open fuse, no AC power to the power center or wrongly wired transformer leads. Jandy codes 126 and 127 mean low input voltage, and 170 to 173 are board, wiring or sensor faults. CircuPool lists a tripped reset and input power or wiring problems.
What to do
- Switch the generator off at the circuit breaker and leave it off.
- Don't open the control unit or test live wiring yourself. Call a licensed electrician for anything involving the supply, the breaker, the voltage or the wiring.
- For a board, sensor or cell fault, call the manufacturer's support line with the model and the code or lights showing.
- PHTA says a generator should be electrically interlocked with the circulation pump so it loses power when the pump stops. If it has power with the pump off, have an electrician look.
- Keep the free chlorine up with an outside source until it is repaired.
A cold-water or low-temperature message
What is the pool water temperature on a thermometer?
In the 50s °F or colder
Keep an eye on it
The cold-water cutoff is working as designed
Every maker switches production off in cold water to protect the cell. Hayward stops below 50°F, Pentair at 52°F give or take 3°F, Jandy below 51°F, and CircuPool steps output down below 68°F and 59°F before stopping below 53°F. Very little chlorine is needed in cold water, and Hayward notes that bacteria and algae stop growing at its cutoff temperature.
What to do
- Don't try to fix it. The cell restarts once the water warms past the cutoff.
- Keep testing free chlorine every week or so. If it falls toward zero, add chlorine from an outside source.
- To force production for a day, Hayward lets you switch to Super Chlorinate and Jandy offers Boost for 24 hours. Pentair describes no override, so use an outside source.
- Lower the output setting in cold weather so the pool doesn't overshoot when the cell restarts.
Well above that, in the 60s °F or warmer
Deal with it soon
A cold or temperature message in warm water points to heat or the sensor
On a Hayward the flashing Generating light means the water is too hot or too cold to operate, so it can appear in a heat wave. Jandy code 174 means the sensor reads above 108°F, and CircuPool cuts output on its own when it senses overheating. If a thermometer shows a normal temperature, the unit's temperature sensor is probably dirty or has failed.
What to do
- Check the water temperature at the return with a thermometer and compare it with the unit's reading. Hayward's diagnostic button shows the temperature it sees.
- On a Jandy, clean the flow, temperature and salinity sensor contacts. Codes 181 to 186 are probe faults that need the manufacturer.
- If the water is hot, cool it or wait. If the sensor is wrong, contact the manufacturer for service.
No warning, but free chlorine keeps testing low
What do your tests show?
Test free chlorine, cyanuric acid (CYA) and salt with a kit, not the generator's own display.
CYA is low, in a pool that gets full sun
Deal with it soon
Low stabilizer lets the sun burn the chlorine off
Without stabilizer, sunlight destroys most chlorine within about 2 hours, so a generator can run all day and the pool still tests low. Hayward, Pentair and CircuPool all want 30 to 50 ppm of CYA. Jandy's range is higher, 50 to 75 ppm, and 75 to 85 ppm once the water passes about 30°C. Salt generators add no stabilizer of their own, as PHTA notes. Indoor pools are different: Pentair says not to use CYA indoors.
What to do
- Test CYA with a kit. If it's under your brand's range, raise it with the CYA calculator.
- Raise it in stages and retest, as CYA dissolves slowly.
- Don't overshoot. CircuPool says to keep it from rising much above 50 ppm, because too much stabilizer cuts chlorine's effectiveness.
- Check CYA whenever you check salt. Hayward notes the two usually decline together, and Jandy's salt instructions add stabilizer along with the salt.
CYA and salt are in range, but chlorine falls after heat, rain or a busy weekend
Deal with it soon
Output or run time can't keep up with the chlorine demand
With salt and CYA in range, chlorine falls short when the cell can't make enough in the hours the pump runs, or when demand jumps. Between them the manuals list an output setting that is too low, too few pump hours, hot weather, heavy use, rain or leaves, new water that was never shocked, and phosphates, nitrates or metals in the water.
What to do
- Raise the output setting a step at a time and retest after 24 hours.
- Lengthen the pump run. Hayward says 8 hours for an average pool, and CircuPool asks for the whole pool to pass through the filter 1.5 to 2 times a day.
- After a party, storm or heavy use, use the boost or super-chlorinate mode for 24 hours. If chlorine is still low, shock from an outside source.
- If nothing helps, take a water sample to a pool service technician for a phosphate, nitrate and metals test, which the manuals name as hidden chlorine eaters.
I haven't tested CYA or salt yet
Deal with it soon
Get a trustworthy salt reading before you do anything else
The generator's own salt display is an estimate. Pentair's sensor is accurate only to within 500 ppm, Jandy notes that temperature affects its reading and that test strips can vary by 400 to 800 ppm, and Hayward advises a separate check before large additions. The ranges differ by brand: Hayward 2700 to 3400 ppm, Pentair 3600 to 4500 ppm, Jandy 3.0 to 3.5 gpl and CircuPool 3000 to 4000 ppm.
What to do
- Test salt with a titration kit or a meter calibrated for sodium chloride, then compare it with your brand's range.
- After any addition, run the pump for 24 hours before testing again.
- Come back to this tree with the new reading.
In short: A salt generator stops for a short list of reasons: no flow, salt under the maker's floor (2600 ppm Pentair, 2.0 gpl Jandy, 2000 ppm CircuPool), scale, cold water (about 50 to 53°F) or low CYA. The tree asks the brand where it matters.
This troubleshooter narrows down likely causes from published guidance; it can't see or test your water. Retest before you add anything, follow the label on every product you use, and call a pool service technician or a licensed electrician for anything electrical, gas-fired or structural.
Handling pool chemicals safely
In the words of the public-health agencies:
Chemicals shall be added to water when diluting as opposed to adding water to a concentrated chemical.
(MAHC 2024, 5.9.3.4.2.2 (a public-pool code) (PDF, opens in a new tab))Two or more chemicals shall never be mixed in the same dilution water.
(MAHC 2024, 5.9.3.4.2.3.1 (a public-pool code) (PDF, opens in a new tab))If label directs pre-dissolving, add the pool chemical to water. NEVER add water to the pool chemical because a violent (potentially explosive) reaction can occur.
(CDC, Use Pool Chemicals Safely (PDF, opens in a new tab))Store each pool chemical separately in a dedicated location.
(CDC, Pool Chemical Safety (opens in a new tab))Do not mix old chemicals with fresh chemical, even if they are the same type
(EPA 550-F-01-003 (PDF, opens in a new tab))Never mix:
(CDC, Use Pool Chemicals Safely (PDF, opens in a new tab))Chlorine products with acid; this could create toxic gases.
Different pool chemicals (for example, different types of chlorine products) with each other or with any other substance.
Get new tools by email
When we add a tool to Pool Chemical Log, we'll send you one short email. Nothing else.
This troubleshooter is for a pool with a salt chlorine generator that has stopped making chlorine, or is making too little. It starts from the one thing every owner can see, the lights or messages on the control panel, and where the fault depends on the maker it asks whether the unit is a Hayward AquaRite, a Pentair IntelliChlor, a Jandy AquaPure or a CircuPool CORE. The advice comes from those makers' own manuals and PHTA's fact sheet on generators. When the fault is electrical, it sends you to a licensed electrician or the manufacturer rather than a repair guide.
Worked example: a Hayward pool with a flashing Inspect Cell light
An 18,000-gallon plaster pool on a Hayward AquaRite tests at 0.5 ppm free chlorine, even though the unit has been running all week. The Inspect Cell light is flashing, the salt display reads 3100 ppm, and the last CYA test came in at 20 ppm.
Following the tree: the message is a cell warning, so the first branch is the cell, and the cell comes out with the power off at the breaker. Light-colored crusty deposits sit on the plates, which is scale. Hayward describes a flashing light as the cell reporting reduced efficiency or a scheduled inspection, and a steady light as "cell efficiency is greatly reduced", with chlorine production stopped. The salt reading of 3100 ppm sits inside Hayward's 2700 to 3400 ppm range, so salt is ruled out as the cause.
The scale is one finding. The CYA is a second, found only because the tree asks about it: 20 ppm is under the 30 to 50 ppm that Hayward's maintenance schedule lists, so sunlight is stripping the chlorine as quickly as the cell makes it. The fixes are a hose-down of the plates and a CYA raise, which the cyanuric acid calculator sizes. A faulty cell would not have been the answer here, which is why the tree checks salt, scale and stabilizer before it suggests a replacement.
The same fault, in four vocabularies
The makers use different words for the same conditions, and that is the main reason a generic guide fails.
- No flow. Hayward says its flow switch "has detected no water flowing", and Pentair shows a red Flow light. Jandy shows NO FLOW on its display, and CircuPool lights a NO FLOW LED. In every case the cell has been shut off on purpose.
- Low salt. Hayward flashes Check Salt, Pentair turns the salt light red, Jandy shows ADD SALT and CircuPool lights Low Salt. The exact thresholds differ, which is why the tree asks the brand before it gives a number.
- High salt. Hayward and Jandy shut down. Pentair flashes its green light. CircuPool describes no high-salt light in its manual.
- Cell. Hayward's Inspect Cell, Pentair's flashing green cell light, Jandy's service code 125 and CircuPool's Clean Cell all mean the plates need attention. Pentair's manual adds that "The blades may have calcium buildup."
Salt: one idea, four sets of numbers
Salt is the most common cause, and the makers disagree on the figures, so a salt reading means little without the brand. Hayward gives a range of 2700 to 3400 ppm and flashes Check Salt below the bottom of it. Pentair prefers 3600 to 4500 ppm, shows red under 2800 ppm and cuts the cell off under 2600 ppm. Jandy works in grams per liter, where 1 gpl is 1000 ppm, wants 3.0 to 3.5 gpl and turns the cell off below 2.0 gpl. CircuPool suggests 3000 to 4000 ppm and lights Low Salt below 2000 ppm.
Two cautions apply to every reading. The panel's figure is an estimate: Pentair says its sensor is only accurate to within 500 ppm, and Jandy warns that test strips vary by 400 to 800 ppm. And salt takes time to mix. Hayward and Pentair both say to run the pump for a full 24 hours after adding salt before trusting the display. For the pounds needed, use the pool salt calculator, which takes its targets from the same manuals.
Too much salt is a different kind of problem. PHTA notes that excess salt raises the risk of corrosion and makes the water taste and feel more like seawater, and that too little shortens the electrodes' life. Jandy puts the damage bluntly: "Operating with high salt will damage the power center." The remedy in three of the four manuals is dilution, because salt does not evaporate.
Why a cell scales even in balanced water
PHTA is direct that "scale formation will occur inside the ECG even if the pool water is properly balanced". The surface of the cathode plates runs at a high pH, and calcium carbonate is the scale most likely to form there. Balanced water slows the process; it does not stop it. Calcium hardness, pH and alkalinity that drift high speed it up a lot, which is why CircuPool reads frequent buildup as a sign of a chronically high saturation index. The pool LSI calculator shows where the water sits.
Cleaning has a cost. Hosing the plates is gentle. Acid cleaning and polarity reversal both strip a little of the plate coating, and PHTA's warning is blunt: "Excessive acid cleaning will damage the cell." Use the method and the mixing ratio in your own manual, because they differ by brand, and switch the power off first. A cell that scales faster after each cleaning is a sign to fix the water, not the cell.
Cold water, sun and stabilizer
A generator that goes quiet in autumn is usually working as designed. Every maker cuts production in cold water to protect the cell, at about 50°F for Hayward, 52°F for Pentair, 51°F for Jandy and 53°F for CircuPool, which also steps its output down from 68°F. Very little chlorine is needed at those temperatures, but it is worth testing now and then.
Sun is the other quiet cause. Without CYA, the sun destroys most free chlorine within about two hours, so a unit can run flat out and the pool still tests low. Hayward, Pentair and CircuPool each want 30 to 50 ppm; Jandy wants more, 50 to 75 ppm. What cyanuric acid does explains the trade-off with too much.
When to stop and call someone
Anything electrical belongs to a licensed electrician: no power at the unit, a tripped breaker that keeps tripping, a low-voltage code, wiring that doesn't match the diagram. A circuit-board fault, a failed sensor or a worn cell is a job for the manufacturer's support line, with the model and the code on the display to hand. A cell that makes no chlorine with right salt, clean plates and a good flow is rarely a home fix. Meanwhile, keep free chlorine up from an outside source, and log each test in the pool chemistry log, so the next person sees the trend. If the cause was a dirty or leaking filter, the pool filter troubleshooter picks up from there.
Sources (5)
- Hayward, AquaRite 900 manual hayward.com
- Pentair, IntelliChlor IC15–IC60 installation and user's guide pentair.com
- Jandy, AquaPure PureLink manual (H0325600) jandy.com
- CircuPool, CORE series manual circupool.com
- PHTA, Electrolytic Chlorine Generators fact sheet (2021) phta.org