Cloudy Pool Water Troubleshooter: Why Is My Pool Cloudy?
Updated
Why is my pool water cloudy?
Start with what you can see, then bring a fresh DPD test. If you cannot make out the main drain at the deep end, keep everyone out of the water: the MAHC 2024, a public-pool code, counts a pool whose bottom is not visible as an imminent health hazard, and a good home-pool rule follows it.
What color is the cloudiness?
Look at the deep end in daylight, then fill a clear glass and hold it against something white.
White, milky or grey
What does a DPD test show for free chlorine?
CDC advises a DPD kit over strips. If the reagent color flashes and then fades to clear, the sample may be bleaching out, so dilute it with tap water and retest.
Below the minimum: under 1 ppm, or under 2 ppm if the pool has CYA
Subtract free chlorine from total chlorine. What is the combined chlorine?
Combined chlorine is chlorine already tied up with swimmer waste. The MAHC 2024, a public-pool code, sets 0.4 ppm as the level to act on.
More than 0.4 ppm
Act now
Chloramines and low free chlorine
Low free chlorine with combined chlorine above 0.4 ppm means the chlorine you added is being used up as fast as it goes in, forming chloramines. Michigan State University Extension's manual calls breakpoint chlorination, which adds free chlorine at 10 times the combined chlorine, the accepted way to remove chloramines and the debris that causes cloudy water.
What to do
- Shock to breakpoint: the pool shock calculator takes the larger of the gap to your target and 10 times your combined chlorine.
- Add the shock all at once with the pump running, so the whole pool reaches breakpoint together, and keep swimmers out until free chlorine falls back to the normal range.
- Retest total and free chlorine the next day; combined chlorine should fall toward zero.
0.4 ppm or less
Act now
Free chlorine too low to hold the water clear
Chlorine is below the CDC minimum of 1 ppm, or 2 ppm with CYA, and there are not many chloramines, so the chlorine is being consumed by something else: sunlight with no CYA, contamination from swimmers, or early algae you cannot yet see.
What to do
- Raise free chlorine with the pool chemical calculator, then retest in a few hours to see how much stays.
- If it falls quickly again, work through the chlorine-keeps-dropping troubleshooter rather than adding more every day.
- Run the filter continuously until the water clears; dead organic matter still has to be filtered out.
At or above the minimum
What is the pH?
Above 7.8
What is the total alkalinity?
If the pool has a lot of CYA, the alkalinity test reads high. The MAHC Annex, guidance for public pools, subtracts one third of the CYA reading from it.
Above 180 ppm
Deal with it soon
High alkalinity and high pH
The MAHC Annex, guidance for public pools, names cloudy water among the problems of high total alkalinity, alongside weaker disinfection, scale and filter trouble. The MAHC 2024, a public-pool code, keeps alkalinity at 60 to 180 ppm.
What to do
- Lower alkalinity first, with acid in small doses, then bring pH down; the order matters.
- Retest after each step and let the water circulate before the next dose.
- Run the filter while the water clears.
180 ppm or lower
Deal with it soon
High pH with alkalinity in range
pH above 7.8 weakens chlorine, and CDC says the effect is strongest above 8.0. High pH also pushes calcium carbonate out of solution, which clouds the water and can leave scale. How much depends on alkalinity, calcium hardness and temperature together, which the Langelier saturation index combines.
What to do
- Lower pH in small doses of acid, retesting between doses.
- Check calcium hardness and run the saturation index to see whether the water is scale-forming.
- Once pH is in range, check that free chlorine is holding.
7.0 to 7.8
How are the filter and the pump?
Compare the filter's pressure gauge with the reading you noted when the filter was last clean.
Pressure is 10 to 12 psi above the clean reading, or the flow from the returns is weak
Deal with it soon
Dirty or failing filter
Michigan State University Extension's manual says a dirty filter slows the flow and can cause cloudy water, and lists a rise of 10 to 12 psi over the clean reading, a lower flow, and cloudy water with debris still in it as the signs to clean or backwash.
What to do
- Backwash a sand filter, clean a cartridge, or clean and recoat a DE filter, following the manufacturer's manual.
- Check the skimmer and pump baskets for blockage.
- If the pressure climbs again soon after cleaning, ask a pool service technician to inspect the filter.
The pump runs only a few hours a day
Deal with it soon
Not enough circulation
Michigan State University Extension's manual says one turnover, a full pass of the pool's water through the filter, takes out only about 68% of the particles, and two turnovers about 96%. A public pool runs its system around the clock for that reason, and a pump on a short timer cannot catch up with what swimmers and weather add.
What to do
- Run the pump continuously until the water clears, then lengthen the daily run time.
- Work out your pool's volume and the pump's flow to see how long one turnover takes.
- Make sure the skimmer and pump baskets are clear and the valves are open.
Pressure and run time both look normal
Which of these fits?
Powder or granules were tossed in by hand, or soda ash, filter aid or a clarifier went in recently
Keep an eye on it
Chemicals added the wrong way
Michigan State University Extension's troubleshooting table lists hand-fed filter aid, soda ash or powdered chlorine as a cause of cloudy water, because the powder makes hardness compounds precipitate. The fix is to dissolve powders and add them as the product label directs.
What to do
- Run the filter continuously so it can catch the precipitate.
- Backwash or clean the filter if the pressure has risen.
- In future, follow the label for how each product is added. The manual says powdered chemicals should be put in solution before they go into the pool.
Heavy swim use, a party, a storm or lots of leaves and dust
Deal with it soon
Heavy swimmer or debris load
Michigan State University Extension's table lists additional bather load as a cause of cloudy water, and recommends superchlorinating and limiting use. Swimmers add the nitrogen compounds that become chloramines, and storms add organic matter that the chlorine has to burn off.
What to do
- Test free and combined chlorine; if combined chlorine is above 0.4 ppm, shock to breakpoint.
- Skim and vacuum debris, and clean the filter baskets.
- Run the pump continuously until the water clears, and retest chlorine before the next swim.
The water is old and rarely topped up, or the pool is on a salt system
Deal with it soon
Too many dissolved solids
Michigan State University Extension's manual says that when total dissolved solids are high the water looks pale and cloudy and test results become erratic, and that dilution with fresh water is the only cure. It cites 1,500 ppm as the level to stay under. PHTA's water chemistry guidelines give the same figure, over any salt a chlorine generator adds at startup.
What to do
- Get a TDS reading from a pool supply store or a pool service technician.
- If it is high, drain part of the pool and refill with fresh water, within the limits of your pool's construction and local rules.
- Do not drain an in-ground pool where the water table is high; the manual warns a pool can float, move or crack.
None of these
Keep an eye on it
Nothing here explains it
If chlorine, pH, alkalinity, the filter and the circulation all check out and the water is still cloudy, the cause may be outside what a home test kit measures: fine particles the filter passes, metals, or a test that is giving wrong readings.
What to do
- Retest with fresh reagents, since Michigan State University Extension's manual stresses that worn reagents give unreliable readings.
- Take a water sample to a pool supply store or a pool service technician for a full analysis.
- Keep a dated record of every test so whoever helps can see the trend.
Below 7.0
Deal with it soon
Low pH
CDC wants pH between 7.0 and 7.8. Michigan State University Extension's manual lists cloudy water, red eyes, staining and equipment damage for low pH, and the MAHC Annex, guidance for public pools, adds that low pH can dissolve calcium from plaster and speed metal corrosion.
What to do
- Test total alkalinity too: low alkalinity is the usual reason pH will not stay put.
- Raise alkalinity first with baking soda if it is low, then retest pH before touching it.
- Retest after each adjustment; do not stack doses.
The color flashes and fades, or the test reads 0 in water that smells strongly of chlorine
Act now
The test may be bleaching out
CDC warns that when free chlorine is above 10 ppm the reagent can bleach out and show a false low or a reading of 0. Michigan State University Extension's manual describes the same sign: the color shows and then disappears. Adding more chlorine to a reading that is falsely low makes the problem worse.
What to do
- Do not add chlorine. Dilute a fresh sample with a known amount of tap water, test it, and multiply by the dilution (a 1-to-1 dilution doubles the reading).
- If the true reading is above 10 ppm, keep swimmers out until it falls; the MAHC 2024, a public-pool code, treats that level as an imminent hazard with bathers present.
- Rinse the viewing tube thoroughly: leftover reagent also gives false results.
Green or yellow-green
Where does the green show?
Through all the water, and the bottom is hard to see
Act now
Algae bloom
Green cloudiness through the whole pool is algae growing faster than the chlorine can kill it. Michigan State University Extension's manual lists a turbid, dirty look, itchy swimmers, extra chlorine demand and a clogged filter among the things algae does. A pool whose bottom cannot be seen should not be swum in.
What to do
- Keep swimmers out until you can see the main drain clearly.
- Test free chlorine, combined chlorine, pH and CYA before dosing. High CYA slows chlorine's kill rate, and the MAHC Annex, guidance for public pools, notes algae may need a higher free chlorine or a lower CYA-to-chlorine ratio.
- Brush the walls and floor, then shock to the target the pool needs and run the filter continuously until the water is clear.
- Retest after each dose; a second, smaller dose is common.
In patches on walls, steps or the floor, with the water mostly clear
Deal with it soon
Algae on surfaces
Black and yellow algae attach to walls, floors and steps and are hard to remove once they hold. Michigan State University Extension's manual says black algae needs a stainless steel brush to break its outer wall so chlorine can reach it, and yellow algae responds to brushing.
What to do
- Brush every affected surface before you dose. The manual calls for a stainless steel brush on black algae; check your pool surface manufacturer before using one.
- Raise free chlorine to the shock level the pool needs, then filter continuously.
- Check the filter for algae and clean it if the pressure has risen.
Brown, tan or rust-colored
Deal with it soon
Dissolved minerals or algae
Michigan State University Extension's troubleshooting table lists green to reddish-brown water as algae and minerals, and tells the operator to check for iron, copper and manganese. Brown or tan cloudiness that appears after adding chemicals or fill water often points to metals coming out of solution.
What to do
- Test pH, total alkalinity and calcium hardness, since the manual says corrosive water can attack the metal parts of the equipment and discolor the water.
- Have the water tested for iron, copper and manganese at a pool supply store or by a pool service technician before using a sequestering agent.
- Follow the sequestering product's label, and retest pH and alkalinity afterward.
In short: Cloudy water has a short list of causes: free chlorine under CDC's 1 ppm (2 ppm with CYA), combined chlorine over 0.4 ppm, pH over 7.8, alkalinity over 180 ppm, or a dirty filter. Michigan State University Extension's manual and the MAHC 2024, a public-pool code, give the tests that sort them.
This troubleshooter narrows down likely causes from published guidance; it can't see or test your water. Retest before you add anything, follow the label on every product you use, and call a pool service technician or a licensed electrician for anything electrical, gas-fired or structural.
Get new tools by email
When we add a tool to Pool Chemical Log, we'll send you one short email. Nothing else.
This troubleshooter is for a home pool whose water has gone milky, hazy, dull or faintly green and stays that way after a day or two. It asks about the color of the cloudiness, then about a DPD test of free chlorine, combined chlorine, pH and alkalinity, and then about the filter and the pump, and it stops at the first cause that fits. It cannot see your water, so each result is a lead to confirm with a fresh test before anything is added.
Worked example: milky water in a plaster pool
A plaster pool with a cartridge filter turned milky white over a weekend. A DPD test shows free chlorine at 3.0 ppm, combined chlorine at 0.2 ppm, pH 7.9, total alkalinity 210 ppm and CYA 40 ppm. The troubleshooter's path is white or milky, then free chlorine at or above the minimum, then pH above 7.8, then alkalinity above 180 ppm.
The result is high alkalinity with high pH. Because CYA is in the water, the alkalinity reading needs one correction first. The MAHC Annex, guidance for public pools, explains that CYA inflates the alkalinity test and tells the operator to divide the CYA reading by 3 and subtract it. Here that is 40 divided by 3, about 13, so the corrected alkalinity is about 197 ppm, still over the 180 ppm top of the range in the MAHC 2024, a public-pool code. The same Annex names cloudy water among the problems of high alkalinity. The fix is alkalinity first, then pH, in small doses with a retest between, which the guide to lowering pH lays out and the pH and alkalinity calculator sizes.
When you cannot see the bottom
If the main drain at the deep end is not visible, keep everyone out of the water until it is. The MAHC 2024, a public-pool code, counts a pool bottom that is not visible among its imminent health hazards, and the reasoning carries over to a backyard pool: nobody can see a swimmer in trouble. Cloudiness also hides algae, and a bloom that reaches this stage needs the sequence in the green pool guide rather than a single dose.
The causes, in the order the tool checks them
Low free chlorine. CDC asks for at least 1 ppm free chlorine in a pool, and at least 2 ppm when the water holds CYA. Below that, organic matter and young algae build faster than chlorine clears them, and the water dulls before it turns green. If free chlorine will not stay up after you raise it, the cause is the subject of the chlorine-keeps-dropping troubleshooter.
Chloramines. Chlorine that has combined with swimmer waste still shows up on a total chlorine test but does little work. Michigan State University Extension's manual describes breakpoint chlorination, free chlorine added at 10 times the combined chlorine, as the accepted way to remove chloramines, and says it also removes the debris that causes cloudy water. The same manual gives the rule for a shock: add it all at once, so the whole pool reaches breakpoint together. The pool shock calculator does the arithmetic. The smell side of the problem is covered in the chlorine smell troubleshooter.
High pH and high alkalinity. CDC keeps pH between 7.0 and 7.8 and notes that chlorine kills germs more slowly as pH rises, especially above 8.0. Michigan State University Extension's manual lists cloudy water among the results of both low and high pH. At high pH, calcium carbonate leaves solution and clouds the water or crusts as scale.
The filter and the pump. The manual says a dirty filter slows the flow and can cause cloudy water, and gives three signs it needs cleaning: pressure 10 to 12 psi over the clean reading, a drop in flow, and cloudiness with debris still in the water. It also says one turnover of the pool's water through the filter removes only about 68% of the particles, and two turnovers about 96%, which is why a public pool circulates around the clock. A pump on a short timer cannot keep up.
Causes that look like chemistry but are not
Three less common causes are in the manual's troubleshooting table. Powdered chemicals tossed in by hand, such as soda ash, filter aid or powdered chlorine, can make hardness compounds precipitate, so powders belong in solution before they go into the pool. A heavy swimmer load calls for shocking and for limiting use. And a high level of total dissolved solids makes the water look pale and cloudy, with erratic test results, which only dilution with fresh water corrects. The manual gives 1,500 ppm as the level to stay under, and PHTA's water chemistry guidelines give the same figure for total dissolved solids, counted above any salt a generator adds at startup.
What changes the answer
The order of the tool is not arbitrary. Free chlorine comes first because a low reading makes every other reading hard to trust. pH and alkalinity come before the filter because a filter cannot clear water that keeps precipitating new particles. Test kits matter too: CDC advises a DPD kit over strips, and warns that a sample over 10 ppm may bleach the reagent and show a false low or a zero, so a pool that is cloudy with a strong smell and a "zero" chlorine test may hold far more chlorine than it reads. Dilute the sample and retest before adding anything.
When to call for help
If every reading is in range, the filter is clean and the pump has run continuously for a few days and the water is still cloudy, take a sample to a pool supply store or a pool service technician for a full analysis. Metals, very fine particles and test-kit errors are all invisible to a basic kit. A brown, tan or rust-colored cloudiness is a separate case: the manual's table lists it as algae or dissolved minerals and recommends testing for iron, copper and manganese. Keep a dated record of every test, so whoever helps can see the trend rather than one result.
Sources (5)
- Michigan State University Extension, Swimming Pool Pest Management, Category 5A manual canr.msu.edu
- CDC, Home Pool and Hot Tub Water Treatment and Testing cdc.gov
- CDC, Model Aquatic Health Code, 2024 (5th edition): Code, a public-pool code cdc.gov
- CDC, Model Aquatic Health Code, 2024 (5th edition): Annex, guidance for public pools cdc.gov
- PHTA, Pool & Spa Management (2021), Appendix B: Water Chemistry Guidelines & Worksheets phta.org